Violin Forum/Message Board Forum Index Violin Forum/Message Board
Provided by Violin Vision
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Search found 10 matches
Violin Forum/Message Board Forum Index
Author Message
  Topic: Varnished fiddle smells bad
SioFong Tong

Replies: 4
Views: 6843

PostForum: Violin Making and Restoration Forum   Posted: Sat Mar 23, 2019 1:33 am   Subject: Varnished fiddle smells bad
May be rancid and not dried fully? I have some dried rancid oil. It doesn’t smell bad after it dried.
  Topic: Tapering rib assembly from top to bottom
SioFong Tong

Replies: 5
Views: 7276

PostForum: Violin Making and Restoration Forum   Posted: Sun Sep 30, 2018 12:47 pm   Subject: Tapering rib assembly from top to bottom
Usually my taper is on the top side because my neck block is 31mm height when glued to the mould. The others blocks are 33,32mm.

I sand more on the side with higher linings. So sometime the taper i ...
  Topic: Joining plate wood ?
SioFong Tong

Replies: 18
Views: 19902

PostForum: Violin Making and Restoration Forum   Posted: Mon Apr 02, 2018 2:09 am   Subject: Joining plate wood ?
Jethro,
I always keep my room humidity in between 50-60Rh. After resaw if, I wait for at least one week because sometimes the wood will bend after resaw. Here in my city the humidity can go as high a ...
  Topic: First Build (amateur), based on Plowden poster
SioFong Tong

Replies: 18
Views: 17937

PostForum: Violin Making and Restoration Forum   Posted: Mon Feb 12, 2018 12:11 am   Subject: First Build (amateur), based on Plowden poster
Your varnishing is better than what I did on my first 5-10violins!
  Topic: Joining plate wood ?
SioFong Tong

Replies: 18
Views: 19902

PostForum: Violin Making and Restoration Forum   Posted: Fri Dec 01, 2017 11:43 am   Subject: Joining plate wood ?
My maple can change a lot. I have try plane the maple joint perfect flat and waited for weeks. They can change to concave or convex in different room humidity.

Mine are deep flame maple. They soa ...
  Topic: Hide Glue Experiment
SioFong Tong

Replies: 13
Views: 13003

PostForum: Violin Making and Restoration Forum   Posted: Fri Nov 24, 2017 1:18 am   Subject: Hide Glue Experiment
My experience is one of my unsized deep flame maple plate was failed after 30minutes because the flame sucked all the glue in the end grain.


I think Maple can suck gelled glue as block endgrain ...
  Topic: Hide Glue Experiment
SioFong Tong

Replies: 13
Views: 13003

PostForum: Violin Making and Restoration Forum   Posted: Thu Nov 23, 2017 8:15 am   Subject: Hide Glue Experiment
I always have a little bit of hollow in the middle. it can just close perfectly without any clamp by a rubbed joint. After glued, there is no visible line under a 60x magnifiers.

Clamps are just ...
  Topic: Strad Viola Posters
SioFong Tong

Replies: 2
Views: 4045

PostForum: Violin Making and Restoration Forum   Posted: Sun Nov 19, 2017 2:31 pm   Subject: Strad Viola Posters
Hope strad will reprint these viola poster. I want the vitale.

The bros Amati viola book is good. You may like it. The graduation in the book is +0.5to0.7mm thicker than the strad poster on the sam ...
  Topic: cutting the purfling channel
SioFong Tong

Replies: 45
Views: 40692

PostForum: Violin Making and Restoration Forum   Posted: Mon Nov 13, 2017 10:49 am   Subject: cutting the purfling channel
A gewa style single blade cutter works really well. Hold it like a pen and 'writing' on the edge. It is not hard to cut a no mistake purfling grove with it.
But it take time.

I have dictum style a ...
  Topic: My first build
SioFong Tong

Replies: 6
Views: 6657

PostForum: Violin Making and Restoration Forum   Posted: Wed May 24, 2017 11:14 am   Subject: My first build
Martin, good job!

I play guitar when i was a teenager. At that time I liked spruce guitar color than the orange brown cedar. And always have a question why violin can not in white as a spruce guit ...
 
Page 1 of 1
All times are GMT - 4 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group