View previous topic :: View next topic |
Author |
Message |
ctviolin Super Member
Joined: 07 May 2009 Posts: 961 Location: Roswell
|
Posted: Mon Aug 26, 2013 11:08 am Post subject: |
|
|
Michael Darnton wrote: | Anyone mind if I change the name of this thread to "Cold Bending of Ribs", edit it a bit to reflect that, and make it sticky? |
I wouldn't mind at all - please, go ahead and change it. _________________ Look,
Listen,
Learn. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
DonLeister Moderator
Joined: 29 Mar 2007 Posts: 383 Location: Richmond, VA
|
Posted: Wed Aug 28, 2013 7:31 am Post subject: |
|
|
I don't mind the editing and making it a new thread.
I should make it clear, in case it isn't, that I have to use my bending iron with considerable heat to make the ribs conform to the form.
Craig, I didn't realize until just now, are you bending your ribs without heat?
I just read the SCAVM article and it describes using an iron. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
ctviolin Super Member
Joined: 07 May 2009 Posts: 961 Location: Roswell
|
Posted: Wed Aug 28, 2013 9:48 am Post subject: |
|
|
DonLeister wrote: | I don't mind the editing and making it a new thread.
I should make it clear, in case it isn't, that I have to use my bending iron with considerable heat to make the ribs conform to the form.
Craig, I didn't realize until just now, are you bending your ribs without heat?
I just read the SCAVM article and it describes using an iron. |
Sorry that I didn't answer this sooner.
You're talking about the forms that I use to wet bend the ribs right? yes - no heat is used in that process. At least that's the way I learned, and the way I bend with the forms.
The ribs are bent with pressure and water only. The plastic I put between the upper and lower bout ribs - is that so I can bend two ribs to the correct form at one time. If I don't use a strip of plastic between them, the ribs tend to want to stick or bind a bit, one to the other. Otherwise, they could (or perhaps should) be bent separately, one at a time.
I'm going to bend the two C bout ribs, which are bent separately, and show that being done.
Please - ask away - to me this is an interesting process to do and to share, and I'm more that happy to answer any questions about it.
I'm also going to add a brief discussion about what I would consider the the weaker aspects of the process are, because there are some areas where a bending iron is really helpful.
Not strictly necessary, but helpful.
In particular, with people who like to use thicker and/or heavily figured ribs - I think that the cc bouts, in any case, can be formed much easier with the help of an iron... because the bends are much more "compact" or "curved" than the upper or lower bout ribs are.
Oh well - that's what I've found to be the case. Other opinions may vary on the different aspects of cold bending. I guess it would depend on how much you (meaning anyone) lean towards this as a primary method. _________________ Look,
Listen,
Learn. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
byacey Member
Joined: 29 Mar 2008 Posts: 105 Location: Edmonton, Alberta
|
Posted: Wed Jul 23, 2014 9:37 pm Post subject: Re: Ok you guy`s |
|
|
ctviolin wrote: |
First I wet them through, then I put a scrap of plastic in between them, so they do not grab one another and are able to slide past one another, thern I put them in the form, and slowly tighten the tight part of the curve that is where the block is, down, and put clamps on the large curve (which would bend around the mold fairly easily anyway), but what the heck, might as well get them curved now.
Then I let them dry in the mold for a day or two, or until I'm ready for them. Usually I'll put them outside in the New Mexico sun to dry... I believe that being outside helps the wood somehow - perhaps it simply helps things dry out completely.
| My mentor taught me something very similar.
He would throw the cut rib stock into a pan of boiling water for about five minutes, and then quickly pull them out with tongs and bend them on the forms. We used a stainless steel sheet metal backing, and clamp the ribs in the forms between the form and the backing. Then he would toss the whole thing into a 200F oven for an hour or so. The ribs had very little spring-back if any, after removed from the forms.
I mostly use a bending iron now, but for really highly figured rib stock, the hot water method works better. _________________ Bill |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|